Brocade 40G-QSFP-QSFP-C-1001 Compatible 40G QSFP+ Active Copper Cable, 10m (33ft)

This 40G-QSFP-QSFP-C-1001 compatible ACC cable provides a 40G direct connection for Brocade equipment in a fixed 10m (33ft) configuration. The QSFP+ to QSFP+ assembly integrates both ends and the cable, giving data-center designers one defined product to evaluate for reach, rack layout, airflow and host compatibility.

OEM Part Number: 40G-QSFP-QSFP-C-1001HT Part Number: 40G-QSFP-QSFP-C-1001

Product Highlights

Compatible alternative to Brocade 40G-QSFP-QSFP-C-1001
40G connectivity at 40Gbps
Interface configuration: QSFP+ to QSFP+
Fixed length and part number: 10m (33ft), 40G-QSFP-QSFP-C-1001
Conductor specification: 26AWG
Minimum bend radius: 40mm

Specifications

HT Part Number	40G-QSFP-QSFP-C-1001
Brocade Compatible	40G-QSFP-QSFP-C-1001
Manufacturer	HT
Connector Type	QSFP+ to QSFP+
Max Data Rate	40Gbps
Minimum Bend Radius	40mm
Wire AWG	26AWG
Cable Length	10m (32.81ft)
Jacket Material	PVC (OFNR)
Temperature	0 to 70°C (32 to 158°F)
Protocols	40G InfiniBand 8x DDR, 4x QDR, 10G/40Gigabit Ethernet, Fibre Channel

Cable Construction and Routing

This assembly uses 26AWG conductors, PVC (OFNR) jacket, minimum bend radius 40mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include 40G InfiniBand 8x DDR, 4x QDR, 10G/40Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

Length Selection and Installation Planning

Longer assemblies require disciplined cable dressing. For 40G-QSFP-QSFP-C-1001 at 10m (33ft), use the intended managers rather than a diagonal route across the rack, and leave enough space to release each connector. Any service allowance should be loose and supported, with the complete copper assembly and both connector housings protected throughout the path. The next shorter verified assembly is 40G-QSFP-QSFP-C-0701 at 7m (23ft), which is the better comparison when the managed route leaves substantial unused cable.

Position Within the Length Range

40G-QSFP-QSFP-C-1001 is the longest of 2 verified length options in this family. Compared with 40G-QSFP-QSFP-C-0701 at 7m (23ft), it provides 3m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this assembly, the listed conductor specification is 26AWG; the minimum bend radius is 40mm; the jacket material is PVC (OFNR).

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Standard protective packing is used by default, with project documentation arranged when requested.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. Keep 40G-QSFP-QSFP-C-1001 associated with 10m (33ft) throughout the order and receiving record.

Brocade Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Where supported by the host, link stability and diagnostic indications are reviewed together with the established link.

Frequently Asked Questions

Is this an original Brocade cable?

No. It is an HT-manufactured compatible alternative for equipment that specifies Brocade 40G-QSFP-QSFP-C-1001.

How should an unused assembly be stored?

Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.

Can different brands be connected with the same assembly?

Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.

Does this order code cover multiple lengths?

No. 40G-QSFP-QSFP-C-1001 refers here to 10m (33ft). Every other verified length has a separate part number and page in the length list.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.