OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT 400G OSFP 4 x 100G PAM4 RHS/Flat Top to 400G QSFP-DD 8 x 50G PAM4 Active Optical Cable, 2m (7ft)

Product Highlights

• HT-manufactured AOC assembly in 2m (7ft)
• 400G connectivity at 400Gbps
• Interface configuration: OSFP (RHS/Flat Top) to QSFP-DD
• Fixed length and part number: 2m (7ft), OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT
• Cable construction: AOC
• Maximum power consumption: 14W (OSFP End)10W (QSFP-DD End)
• Minimum bend radius: 30mm
• Operating temperature: 0 to 70°C (32 to 158°F)

Specifications

Signal and Lane Configuration

The listed modulation format is OSFP-4x 100G-PAM4QSFP-DD-8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include OSFP MSA, QSFP-DD MSA, CMIS 4.0, IEEE 802.3ck-400GAUI-4, IEEE 802.3bs-400GAUI-8. Confirm that the host firmware and port configuration support the same operating mode.

Integrated Optical Assembly

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Length Selection and Installation Planning

OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT provides 2m (7ft) for connections between separated rack units or nearby equipment positions. Plan the route around cable managers and power cords, keeping the assembly free from connector strain while avoiding a large obstruction in the airflow path.

Position Within the Length Range

OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT occupies the middle of this family between OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-1M3FT at 1m (3ft) and OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-3M10FT at 3m (10ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 14W (OSFP End)10W (QSFP-DD End); the jacket material is OFNP.

Power and Thermal Planning

The rated power consumption is 14W (OSFP End)10W (QSFP-DD End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Cable Construction and Routing

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Neutral packaging and customer-specific packing documentation are available on request.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. This page’s fixed configuration is 2m (7ft); another length must be quoted under its corresponding part number.

Generic Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.

Frequently Asked Questions

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.