Mellanox QSFP-200G-2QACxxx Compatible Customized 200G QSFP56 to 2 x QSFP56 Active Copper Breakout Cable

Product Highlights

• HT-manufactured compatible alternative for Mellanox QSFP-200G-2QACxxx
• 200G aggregate connectivity at 200Gbps
• Interface configuration: QSFP56 to 2× QSFP56
• Active Twinax
• Length configurations covered: Customized
• Conductor specification: 30AWG for 3m 28AWG for 5m 26AWG for 7m
• Power consumption: 1.5W
• Operating temperature: 0 to 70°C (32 to 158°F)

Available Lengths and Corresponding Part Numbers

The documented series configuration is Customized. Use the relevant OEM reference below together with the HT identity and required length when requesting a quotation. If another length carries a different OEM part number, it must be reviewed and ordered as that distinct configuration.

Compatible OEM Part Numbers

• QSFP-200G-2QACxxx

Specifications

Applications and Deployment

An ACC link combines copper cabling with active electronics at the connector ends. It avoids separate patch leads but is not interchangeable with a passive DAC merely because the cages look alike. Confirm the supported cable type, lane mode and power allowance on every attached port. For this series, the listed interface is QSFP56 to 2× QSFP56 and the aggregate rate is 200G.

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Cable Construction and Routing

For this assembly, the conductor specification is 30AWG for 3m 28AWG for 5m 26AWG for 7m; the jacket material is PVC (OFNR); the minimum bend radius is 27.5mm for 3m 31.5mm for 5m 36.5.mm for 7m; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 1.5W. These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this series, keep the interface rate, ACC construction and length-specific OEM reference together throughout that review.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QSFP-200G-2QACxxx identifies the product family; the linked page provides the final length-specific identity.

Mellanox Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Frequently Asked Questions